FlexPro 3G With Yagi

This booster system boosts 3G cell phone signal inside buildings for up to 5,000 Sq ft. The wide band Yagi antenna works great where the cell phone reception is spotty and using its multiple dipole design, the yagi antenna captures the weakest of signal and the 72dB gain amplifier makes it multiple times stronger for increased reception.

Key Features

  • Completely eliminates dead zones and dropped call problems
  • Requires no set-up of any kind, just plug the device to the power supply and watch your bars rise
  • This amplifier is compatible with all network technologies: CDMA, TDMA, GSM, AMPS, in addition to 1x and 3x data protocols such as HSDPA, EVDO and EDGE
  • 3 Watts max output uses the full potential of your cell phone’s power
  • Boosts the cell phone signal for both incoming and outgoing calls. That is to and from the cell towers
  • Oscillation indicator to indicate if there is any feedback detected between the external antenna and the base unit
  • Automatic gain control ensures stable operation
  • No Internet connection or contract required
  • Easy install involves no set-up or software
  • FCC approved amplifiers and antennas require no set-up or software installation. Just power up and see your signal rise
  • Risk-free 30 day trial guaranteed.

What’s Included

All the components required to install a complete system are included:

  • a) 72 dB gain amplifier base Unit with power supply
  • b) External directional yagi antenna and mounting brackets -ANT-CM-230W
  • c) Internal dome antenna, sending signal 360 degrees – ANT-CM-222W
  • Two sets of LMR400 cable 30 ft & 75 ft long

Surecall-80059-installation diagram
Instruction Manual

Networks Supported

  • AT&T 2G/3G HSPA voice+ data
  • Verizon 2G/3G voice+ data
  • Sprint 2G/3G voice+ data
  • US Cellular 2G/3G voice+ data
  • Alltel 2G/3G voice+ data
  • T-Mobile 2G/3G/4G HSPS voice+ data
  • Major Canadian Carriers 2G/3G voice+ data
  • All other carriers using Uplink: 824-849/1850-1910 Mhz; Downlink : 869-894/1930-1990Mhz

Technical Specifications

Gains:
Uplink: 824-849/1850-1910 Mhz; Downlink : 869-894/1930-1990Mhz
Standards
CDMA, WCDMA, GSM, EDGE, TDMA and AMPS etc.
Maximum Output Power 3 Watts
Impedance 50 ohms
Noise Figure Maximum 5 dB
VSWR Less than 2:1
Power Transformer Input: AC110V, 60Hz; Output: DC 5V
Antennas
Dual band linear antennas, with maximum 3dBi directional gain
RF Connectors
FME Male connectors on both ends
Power Consumption
<10W
Operating Temp

-20° to +70°C

Dimension
7 x 4.8 x 1.2 inch
Weight
1.5 LB

 

This is a CONSUMER device.
BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider’s consent. Most wireless providers consent to the use of signal boosters. Some providers may not consent to the use of this device on their network. If you are unsure, contact your provider. You MUST operate this device with approv3ed antennas and cables as specified by the manufacturer. Antennas MUST be installed at least 20 cm (8 inches) from any person. You MUST cease operating this device immediately if requested by the FCC or a licensed wireless service provider.
WARNING. E911 location information may not be provided or may be inaccurate for calls served by using this device. Please note, the four largest carriers, namely, AT&T, T-Mobile, Verizon and Sprint, and more than 90 regional carriers have given a blanket consent to all boosters meeting the new certification standards.